forked from mirrors/linux
ARM: dts: imx: Add Y Soft IOTA Draco, Hydra and Ursa boards
These are i.MX6S/DL based SBCs embedded in various Y Soft products. All share the same board design but have slightly different HW configuration. Ursa - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD - parallel WVGA 7" LCD with touch panel - 1x Eth (QCA8334 switch) - USB OTG - USB host (micro-B) Draco - i.MX6S SoC, 512MB RAM DDR3, 4GB eMMC, microSD - parallel WVGA 7" LCD with touch panel - 2x Eth (QCA8334 switch) - USB OTG - USB host (micro-B) - RGB LED (I2C LP5562) - 3.5mm audio jack + codec (LM49350) Hydra - i.MX6DL SoC, 2GB RAM DDR3, 4GB eMMC, microSD - I2C OLED display, capacitive matrix keys - 2x Eth (QCA8334 switch) - USB OTG - RGB LED (I2C LP5562) - 3.5mm audio jack + codec (LM49350) - HDMI - miniPCIe slot Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Michal Vokáč <michal.vokac@ysoft.com> Reviewed-by: Rob Herring <robh@kernel.org> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit is contained in:
Vokáč Michal
Shawn Guo
parent
cc077d00fd
commit
87489ec3a7
5 changed files with 760 additions and 0 deletions
|
|
@ -445,6 +445,9 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
|
|||
imx6dl-wandboard.dtb \
|
||||
imx6dl-wandboard-revb1.dtb \
|
||||
imx6dl-wandboard-revd1.dtb \
|
||||
imx6dl-yapp4-draco.dtb \
|
||||
imx6dl-yapp4-hydra.dtb \
|
||||
imx6dl-yapp4-ursa.dtb \
|
||||
imx6q-apalis-eval.dtb \
|
||||
imx6q-apalis-ixora.dtb \
|
||||
imx6q-apalis-ixora-v1.1.dtb \
|
||||
|
|
|
|||
595
arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
Normal file
595
arch/arm/boot/dts/imx6dl-yapp4-common.dtsi
Normal file
|
|
@ -0,0 +1,595 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
|
||||
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/interrupt-controller/irq.h>
|
||||
#include <dt-bindings/pwm/pwm.h>
|
||||
|
||||
/ {
|
||||
backlight: backlight {
|
||||
compatible = "pwm-backlight";
|
||||
pwms = <&pwm1 0 500000 PWM_POLARITY_INVERTED>;
|
||||
brightness-levels = <0 32 64 128 255>;
|
||||
default-brightness-level = <32>;
|
||||
num-interpolated-steps = <8>;
|
||||
power-supply = <&sw2_reg>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
lcd_display: display {
|
||||
compatible = "fsl,imx-parallel-display";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
interface-pix-fmt = "rgb24";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_ipu1>;
|
||||
status = "disabled";
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
|
||||
lcd_display_in: endpoint {
|
||||
remote-endpoint = <&ipu1_di0_disp0>;
|
||||
};
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
|
||||
lcd_display_out: endpoint {
|
||||
remote-endpoint = <&lcd_panel_in>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
panel: panel {
|
||||
compatible = "dataimage,scf0700c48ggu18";
|
||||
power-supply = <&sw2_reg>;
|
||||
status = "disabled";
|
||||
|
||||
port {
|
||||
lcd_panel_in: endpoint {
|
||||
remote-endpoint = <&lcd_display_out>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
reg_pcie: regulator-pcie {
|
||||
compatible = "regulator-fixed";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pcie_reg>;
|
||||
regulator-name = "MPCIE_3V3";
|
||||
regulator-min-microvolt = <3300000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
gpio = <&gpio3 19 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
reg_usb_h1_vbus: regulator-usb-h1-vbus {
|
||||
compatible = "regulator-fixed";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbh1_vbus>;
|
||||
regulator-name = "usb_h1_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio1 29 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
reg_usb_otg_vbus: regulator-usb-otg-vbus {
|
||||
compatible = "regulator-fixed";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbotg_vbus>;
|
||||
regulator-name = "usb_otg_vbus";
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5000000>;
|
||||
gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
|
||||
enable-active-high;
|
||||
status = "okay";
|
||||
};
|
||||
};
|
||||
|
||||
&fec {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_enet>;
|
||||
phy-mode = "rgmii-id";
|
||||
phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
|
||||
phy-reset-duration = <20>;
|
||||
phy-supply = <&sw2_reg>;
|
||||
phy-handle = <ðphy0>;
|
||||
status = "okay";
|
||||
|
||||
mdio {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
phy_port2: phy@1 {
|
||||
reg = <1>;
|
||||
};
|
||||
|
||||
phy_port3: phy@2 {
|
||||
reg = <2>;
|
||||
};
|
||||
|
||||
switch@0 {
|
||||
compatible = "qca,qca8334";
|
||||
reg = <0>;
|
||||
|
||||
switch_ports: ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
ethphy0: port@0 {
|
||||
reg = <0>;
|
||||
label = "cpu";
|
||||
phy-mode = "rgmii";
|
||||
ethernet = <&fec>;
|
||||
|
||||
fixed-link {
|
||||
speed = <1000>;
|
||||
full-duplex;
|
||||
};
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "eth2";
|
||||
phy-handle = <&phy_port2>;
|
||||
};
|
||||
|
||||
port@3 {
|
||||
reg = <3>;
|
||||
label = "eth1";
|
||||
phy-handle = <&phy_port3>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_hdmi_cec>;
|
||||
ddc-i2c-bus = <&i2c2>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&i2c2 {
|
||||
clock-frequency = <100000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_i2c2>;
|
||||
status = "okay";
|
||||
|
||||
pmic@8 {
|
||||
compatible = "fsl,pfuze200";
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pmic>;
|
||||
reg = <0x8>;
|
||||
|
||||
regulators {
|
||||
sw1a_reg: sw1ab {
|
||||
regulator-min-microvolt = <300000>;
|
||||
regulator-max-microvolt = <1875000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
regulator-ramp-delay = <6250>;
|
||||
};
|
||||
|
||||
sw2_reg: sw2 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
sw3a_reg: sw3a {
|
||||
regulator-min-microvolt = <400000>;
|
||||
regulator-max-microvolt = <1975000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
sw3b_reg: sw3b {
|
||||
regulator-min-microvolt = <400000>;
|
||||
regulator-max-microvolt = <1975000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
swbst_reg: swbst {
|
||||
regulator-min-microvolt = <5000000>;
|
||||
regulator-max-microvolt = <5150000>;
|
||||
};
|
||||
|
||||
vgen1_reg: vgen1 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <1550000>;
|
||||
};
|
||||
|
||||
vgen2_reg: vgen2 {
|
||||
regulator-min-microvolt = <800000>;
|
||||
regulator-max-microvolt = <1550000>;
|
||||
};
|
||||
|
||||
vgen3_reg: vgen3 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vgen4_reg: vgen4 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vgen5_reg: vgen5 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vgen6_reg: vgen6 {
|
||||
regulator-min-microvolt = <1800000>;
|
||||
regulator-max-microvolt = <3300000>;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vref_reg: vrefddr {
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
|
||||
vsnvs_reg: vsnvs {
|
||||
regulator-min-microvolt = <1000000>;
|
||||
regulator-max-microvolt = <3000000>;
|
||||
regulator-boot-on;
|
||||
regulator-always-on;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
leds: led-controller@30 {
|
||||
compatible = "ti,lp5562";
|
||||
reg = <0x30>;
|
||||
clock-mode = /bits/ 8 <1>;
|
||||
status = "disabled";
|
||||
|
||||
chan0 {
|
||||
chan-name = "R";
|
||||
led-cur = /bits/ 8 <0x20>;
|
||||
max-cur = /bits/ 8 <0x60>;
|
||||
};
|
||||
|
||||
chan1 {
|
||||
chan-name = "G";
|
||||
led-cur = /bits/ 8 <0x20>;
|
||||
max-cur = /bits/ 8 <0x60>;
|
||||
};
|
||||
|
||||
chan2 {
|
||||
chan-name = "B";
|
||||
led-cur = /bits/ 8 <0x20>;
|
||||
max-cur = /bits/ 8 <0x60>;
|
||||
};
|
||||
|
||||
chan3 {
|
||||
chan-name = "W";
|
||||
led-cur = /bits/ 8 <0x0>;
|
||||
max-cur = /bits/ 8 <0x0>;
|
||||
};
|
||||
};
|
||||
|
||||
eeprom@57 {
|
||||
compatible = "atmel,24c128";
|
||||
reg = <0x57>;
|
||||
pagesize = <64>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
touchscreen: touchscreen@5c {
|
||||
compatible = "pixcir,pixcir_tangoc";
|
||||
reg = <0x5c>;
|
||||
pinctrl-0 = <&pinctrl_touch>;
|
||||
interrupt-parent = <&gpio4>;
|
||||
interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
|
||||
attb-gpio = <&gpio4 5 GPIO_ACTIVE_HIGH>;
|
||||
reset-gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>;
|
||||
touchscreen-size-x = <800>;
|
||||
touchscreen-size-y = <480>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
clock-frequency = <100000>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_i2c3>;
|
||||
status = "disabled";
|
||||
|
||||
oled: oled@3d {
|
||||
compatible = "solomon,ssd1305fb-i2c";
|
||||
reg = <0x3d>;
|
||||
solomon,height = <64>;
|
||||
solomon,width = <128>;
|
||||
solomon,page-offset = <0>;
|
||||
solomon,prechargep2 = <15>;
|
||||
reset-gpios = <&gpio_oled 1 GPIO_ACTIVE_LOW>;
|
||||
vbat-supply = <&sw2_reg>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
gpio_oled: gpio@41 {
|
||||
compatible = "nxp,pca9536";
|
||||
gpio-controller;
|
||||
#gpio-cells = <2>;
|
||||
reg = <0x41>;
|
||||
vcc-supply = <&sw2_reg>;
|
||||
status = "disabled";
|
||||
};
|
||||
};
|
||||
|
||||
&iomuxc {
|
||||
pinctrl_enet: enetgrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b020
|
||||
MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b020
|
||||
MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b020
|
||||
MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b020
|
||||
MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b020
|
||||
MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b020
|
||||
MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b020
|
||||
MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b020
|
||||
MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b020
|
||||
MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b020
|
||||
MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b020
|
||||
MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b020
|
||||
MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b020
|
||||
MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b020
|
||||
MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b010
|
||||
MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x1b010
|
||||
MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_hdmi_cec: hdmicecgrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1b898
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_i2c2: i2c2grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b899
|
||||
MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b899
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_i2c3: i2c3grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b899
|
||||
MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b899
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_ipu1: ipu1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10
|
||||
MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
|
||||
MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
|
||||
MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10
|
||||
MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10
|
||||
MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10
|
||||
MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10
|
||||
MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10
|
||||
MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10
|
||||
MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10
|
||||
MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10
|
||||
MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10
|
||||
MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10
|
||||
MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10
|
||||
MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10
|
||||
MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10
|
||||
MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10
|
||||
MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10
|
||||
MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10
|
||||
MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10
|
||||
MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10
|
||||
MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10
|
||||
MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10
|
||||
MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10
|
||||
MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10
|
||||
MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10
|
||||
MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_pcie: pciegrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x1b098
|
||||
MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x1b098
|
||||
MX6QDL_PAD_CSI0_DATA_EN__GPIO5_IO20 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_pcie_reg: pciereggrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_pmic: pmicgrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_pwm1: pwm1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_9__PWM1_OUT 0x8
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_touch: touchgrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b098
|
||||
MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_uart1: uart1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0a8
|
||||
MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0a8
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbh1: usbh1grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D30__USB_H1_OC 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbh1_vbus: usbh1-vbus {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x98
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbotg: usbotggrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b098
|
||||
MX6QDL_PAD_EIM_D21__USB_OTG_OC 0x1b098
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usbotg_vbus: usbotg-vbus {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x98
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usdhc3: usdhc3grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x1b018
|
||||
MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b018
|
||||
MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
|
||||
MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
|
||||
MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
|
||||
MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
|
||||
MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
|
||||
MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_usdhc4: usdhc4grp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_SD4_CMD__SD4_CMD 0x1f069
|
||||
MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10069
|
||||
MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17069
|
||||
MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17069
|
||||
MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17069
|
||||
MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17069
|
||||
MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17069
|
||||
MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17069
|
||||
MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17069
|
||||
MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17069
|
||||
>;
|
||||
};
|
||||
|
||||
pinctrl_wdog: wdoggrp {
|
||||
fsl,pins = <
|
||||
MX6QDL_PAD_GPIO_1__WDOG2_B 0x1b0b0
|
||||
>;
|
||||
};
|
||||
};
|
||||
|
||||
&ipu1_di0_disp0 {
|
||||
remote-endpoint = <&lcd_display_in>;
|
||||
};
|
||||
|
||||
&pcie {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pcie>;
|
||||
reset-gpio = <&gpio7 12 GPIO_ACTIVE_LOW>;
|
||||
vpcie-supply = <®_pcie>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
#pwm-cells = <3>;
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_pwm1>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&uart1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_uart1>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh1 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbh1>;
|
||||
vbus-supply = <®_usb_h1_vbus>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&usbotg {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usbotg>;
|
||||
vbus-supply = <®_usb_otg_vbus>;
|
||||
srp-disable;
|
||||
hnp-disable;
|
||||
adp-disable;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy1 {
|
||||
fsl,tx-d-cal = <106>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy2 {
|
||||
fsl,tx-d-cal = <109>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&usdhc3 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usdhc3>;
|
||||
bus-width = <4>;
|
||||
cd-gpios = <&gpio7 8 GPIO_ACTIVE_LOW>;
|
||||
wp-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>;
|
||||
no-1-8-v;
|
||||
keep-power-in-suspend;
|
||||
wakeup-source;
|
||||
vmmc-supply = <&sw2_reg>;
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&usdhc4 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_usdhc4>;
|
||||
bus-width = <8>;
|
||||
non-removable;
|
||||
no-1-8-v;
|
||||
keep-power-in-suspend;
|
||||
vmmc-supply = <&sw2_reg>;
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wdog1 {
|
||||
status = "disabled";
|
||||
};
|
||||
|
||||
&wdog2 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&pinctrl_wdog>;
|
||||
fsl,ext-reset-output;
|
||||
status = "okay";
|
||||
};
|
||||
58
arch/arm/boot/dts/imx6dl-yapp4-draco.dts
Normal file
58
arch/arm/boot/dts/imx6dl-yapp4-draco.dts
Normal file
|
|
@ -0,0 +1,58 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "imx6dl.dtsi"
|
||||
#include "imx6dl-yapp4-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Y Soft IOTA Draco i.MX6Solo board";
|
||||
compatible = "ysoft,imx6dl-yapp4-draco", "fsl,imx6dl";
|
||||
|
||||
memory@10000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x10000000 0x20000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&backlight {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&lcd_display {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&leds {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&panel {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
®_usb_h1_vbus {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&touchscreen {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy2 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usdhc3 {
|
||||
status = "okay";
|
||||
};
|
||||
50
arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
Normal file
50
arch/arm/boot/dts/imx6dl-yapp4-hydra.dts
Normal file
|
|
@ -0,0 +1,50 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "imx6dl.dtsi"
|
||||
#include "imx6dl-yapp4-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Y Soft IOTA Hydra i.MX6DualLite board";
|
||||
compatible = "ysoft,imx6dl-yapp4-hydra", "fsl,imx6dl";
|
||||
|
||||
memory@10000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x10000000 0x80000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&gpio_oled {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&hdmi {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&i2c3 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&leds {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&oled {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
®_pcie {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usdhc3 {
|
||||
status = "okay";
|
||||
};
|
||||
54
arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
Normal file
54
arch/arm/boot/dts/imx6dl-yapp4-ursa.dts
Normal file
|
|
@ -0,0 +1,54 @@
|
|||
// SPDX-License-Identifier: GPL-2.0
|
||||
//
|
||||
// Copyright (C) 2015-2018 Y Soft Corporation, a.s.
|
||||
|
||||
/dts-v1/;
|
||||
|
||||
#include "imx6dl.dtsi"
|
||||
#include "imx6dl-yapp4-common.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Y Soft IOTA Ursa i.MX6Solo board";
|
||||
compatible = "ysoft,imx6dl-yapp4-ursa", "fsl,imx6dl";
|
||||
|
||||
memory@10000000 {
|
||||
device_type = "memory";
|
||||
reg = <0x10000000 0x20000000>;
|
||||
};
|
||||
};
|
||||
|
||||
&backlight {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&lcd_display {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&panel {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&pwm1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
®_usb_h1_vbus {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&switch_ports {
|
||||
/delete-node/ port@2;
|
||||
};
|
||||
|
||||
&touchscreen {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbh1 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&usbphy2 {
|
||||
status = "okay";
|
||||
};
|
||||
Loading…
Reference in a new issue