nagai/kernel
3
0
Fork 0
forked from mirrors/linux
Code Pull requests Activity

e1000: update README for e1000

Browse source 
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
This commit is contained in:
Auke Kok 2006-11-01 08:48:18 -08:00 committed by Jeff Garzik
parent 25006ac61e
commit de3edab427
1 changed files with 244 additions and 163 deletions
repo.diff.show_diff_stats Download patch file Download diff file Expand all files Collapse all files

227
Documentation/networking/e1000.txt
View file

@ -1,7 +1,7 @@
Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
===============================================================
November 15, 2005
September 26, 2006
Contents
@ -9,6 +9,7 @@ Contents
- In This Release
- Identifying Your Adapter
- Building and Installation
- Command Line Parameters
- Speed and Duplex Configuration
- Additional Configurations
@ -41,6 +42,9 @@ or later), lspci, and ifconfig to obtain the same information.
Instructions on updating ethtool can be found in the section "Additional
Configurations" later in this document.
NOTE: The Intel(R) 82562v 10/100 Network Connection only provides 10/100
support.
Identifying Your Adapter
========================
@ -57,22 +61,21 @@ networking link on the left to search for your adapter:
http://downloadfinder.intel.com/scripts-df/support_intel.asp
Command Line Parameters =======================
Command Line Parameters
=======================
If the driver is built as a module, the following optional parameters
are used by entering them on the command line with the modprobe or insmod
command using this syntax:
are used by entering them on the command line with the modprobe command
using this syntax:
modprobe e1000 [<option>=<VAL1>,<VAL2>,...]
insmod e1000 [<option>=<VAL1>,<VAL2>,...]
For example, with two PRO/1000 PCI adapters, entering:
insmod e1000 TxDescriptors=80,128
modprobe e1000 TxDescriptors=80,128
loads the e1000 driver with 80 TX descriptors for the first adapter and 128
TX descriptors for the second adapter.
loads the e1000 driver with 80 TX descriptors for the first adapter and
128 TX descriptors for the second adapter.
The default value for each parameter is generally the recommended setting,
unless otherwise noted.
@ -96,9 +99,9 @@ AutoNeg
Valid Range: 0x01-0x0F, 0x20-0x2F
Default Value: 0x2F
This parameter is a bit mask that specifies which speed and duplex
settings the board advertises. When this parameter is used, the Speed
and Duplex parameters must not be specified.
This parameter is a bit-mask that specifies the speed and duplex settings
advertised by the adapter. When this parameter is used, the Speed and
Duplex parameters must not be specified.
NOTE: Refer to the Speed and Duplex section of this readme for more
information on the AutoNeg parameter.
@ -110,14 +113,15 @@ Duplex
Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
Default Value: 0
Defines the direction in which data is allowed to flow. Can be either
one or two-directional. If both Duplex and the link partner are set to
auto-negotiate, the board auto-detects the correct duplex. If the link
partner is forced (either full or half), Duplex defaults to half-duplex.
This defines the direction in which data is allowed to flow. Can be
either one or two-directional. If both Duplex and the link partner are
set to auto-negotiate, the board auto-detects the correct duplex. If the
link partner is forced (either full or half), Duplex defaults to half-
duplex.
FlowControl
----------
-----------
Valid Range: 0-3 (0=none, 1=Rx only, 2=Tx only, 3=Rx&Tx)
Default Value: Reads flow control settings from the EEPROM
@ -127,14 +131,55 @@ to Ethernet PAUSE frames.
InterruptThrottleRate
---------------------
(not supported on Intel 82542, 82543 or 82544-based adapters)
Valid Range: 100-100000 (0=off, 1=dynamic)
Default Value: 8000
(not supported on Intel(R) 82542, 82543 or 82544-based adapters)
Valid Range: 0,1,3,100-100000 (0=off, 1=dynamic, 3=dynamic conservative)
Default Value: 3
This value represents the maximum number of interrupts per second the
controller generates. InterruptThrottleRate is another setting used in
interrupt moderation. Dynamic mode uses a heuristic algorithm to adjust
InterruptThrottleRate based on the current traffic load.
The driver can limit the amount of interrupts per second that the adapter
will generate for incoming packets. It does this by writing a value to the
adapter that is based on the maximum amount of interrupts that the adapter
will generate per second.
Setting InterruptThrottleRate to a value greater or equal to 100
will program the adapter to send out a maximum of that many interrupts
per second, even if more packets have come in. This reduces interrupt
load on the system and can lower CPU utilization under heavy load,
but will increase latency as packets are not processed as quickly.
The default behaviour of the driver previously assumed a static
InterruptThrottleRate value of 8000, providing a good fallback value for
all traffic types,but lacking in small packet performance and latency.
The hardware can handle many more small packets per second however, and
for this reason an adaptive interrupt moderation algorithm was implemented.
Since 7.3.x, the driver has two adaptive modes (setting 1 or 3) in which
it dynamically adjusts the InterruptThrottleRate value based on the traffic
that it receives. After determining the type of incoming traffic in the last
timeframe, it will adjust the InterruptThrottleRate to an appropriate value
for that traffic.
The algorithm classifies the incoming traffic every interval into
classes. Once the class is determined, the InterruptThrottleRate value is
adjusted to suit that traffic type the best. There are three classes defined:
"Bulk traffic", for large amounts of packets of normal size; "Low latency",
for small amounts of traffic and/or a significant percentage of small
packets; and "Lowest latency", for almost completely small packets or
minimal traffic.
In dynamic conservative mode, the InterruptThrottleRate value is set to 4000
for traffic that falls in class "Bulk traffic". If traffic falls in the "Low
latency" or "Lowest latency" class, the InterruptThrottleRate is increased
stepwise to 20000. This default mode is suitable for most applications.
For situations where low latency is vital such as cluster or
grid computing, the algorithm can reduce latency even more when
InterruptThrottleRate is set to mode 1. In this mode, which operates
the same as mode 3, the InterruptThrottleRate will be increased stepwise to
70000 for traffic in class "Lowest latency".
Setting InterruptThrottleRate to 0 turns off any interrupt moderation
and may improve small packet latency, but is generally not suitable
for bulk throughput traffic.
NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
RxAbsIntDelay parameters. In other words, minimizing the receive
@ -142,7 +187,7 @@ NOTE: InterruptThrottleRate takes precedence over the TxAbsIntDelay and
generate more interrupts than what the Interrupt Throttle Rate
allows.
CAUTION: If you are using the Intel PRO/1000 CT Network Connection
CAUTION: If you are using the Intel(R) PRO/1000 CT Network Connection
(controller 82547), setting InterruptThrottleRate to a value
greater than 75,000, may hang (stop transmitting) adapters
under certain network conditions. If this occurs a NETDEV
@ -158,7 +203,7 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
the overall throughput, we recommend that you load the driver as
follows:
insmod e1000.o InterruptThrottleRate=3000,3000,3000
modprobe e1000 InterruptThrottleRate=3000,3000,3000
This sets the InterruptThrottleRate to 3000 interrupts/sec for
the first, second, and third instances of the driver. The range
@ -168,16 +213,25 @@ NOTE: When e1000 is loaded with default settings and multiple adapters
RX_POLLING (NAPI) and default driver settings.
RxDescriptors
-------------
Valid Range: 80-256 for 82542 and 82543-based adapters
80-4096 for all other supported adapters
Default Value: 256
This value specifies the number of receive descriptors allocated by the
driver. Increasing this value allows the driver to buffer more incoming
packets. Each descriptor is 16 bytes. A receive buffer is also
allocated for each descriptor and is 2048.
This value specifies the number of receive buffer descriptors allocated
by the driver. Increasing this value allows the driver to buffer more
incoming packets, at the expense of increased system memory utilization.
Each descriptor is 16 bytes. A receive buffer is also allocated for each
descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
on the MTU setting. The maximum MTU size is 16110.
NOTE: MTU designates the frame size. It only needs to be set for Jumbo
Frames. Depending on the available system resources, the request
for a higher number of receive descriptors may be denied. In this
case, use a lower number.
RxIntDelay
@ -304,7 +358,7 @@ auto-negotiation process. It should be used when you wish to control which
speed and duplex combinations are advertised during the auto-negotiation
process.
The parameter may be specified as either a decimal or hexidecimal value as
The parameter may be specified as either a decimal or hexadecimal value as
determined by the bitmap below.
Bit position 7 6 5 4 3 2 1 0
@ -337,7 +391,6 @@ Additional Configurations
Configuring the Driver on Different Distributions
-------------------------------------------------
Configuring a network driver to load properly when the system is started
is distribution dependent. Typically, the configuration process involves
adding an alias line to /etc/modules.conf or /etc/modprobe.conf as well
@ -346,11 +399,11 @@ Additional Configurations
To learn the proper way to configure a network device for your system,
refer to your distribution documentation. If during this process you are
asked for the driver or module name, the name for the Linux Base Driver
for the Intel PRO/1000 Family of Adapters is e1000.
for the Intel(R) PRO/1000 Family of Adapters is e1000.
As an example, if you install the e1000 driver for two PRO/1000 adapters
(eth0 and eth1) and set the speed and duplex to 10full and 100half, add
the following to modules.conf or modprobe.conf:
the following to modules.conf or or modprobe.conf:
alias eth0 e1000
alias eth1 e1000
@ -358,7 +411,6 @@ Additional Configurations
Viewing Link Messages
---------------------
Link messages will not be displayed to the console if the distribution is
restricting system messages. In order to see network driver link messages
on your console, set dmesg to eight by entering the following:
@ -369,11 +421,9 @@ Additional Configurations
Jumbo Frames
------------
The driver supports Jumbo Frames for all adapters except 82542 and
82573-based adapters. Jumbo Frames support is enabled by changing the
MTU to a value larger than the default of 1500. Use the ifconfig command
to increase the MTU size. For example:
Jumbo Frames support is enabled by changing the MTU to a value larger than
the default of 1500. Use the ifconfig command to increase the MTU size.
For example:
ifconfig eth<x> mtu 9000 up
@ -390,26 +440,49 @@ Additional Configurations
- To enable Jumbo Frames, increase the MTU size on the interface beyond
1500.
- The maximum MTU setting for Jumbo Frames is 16110. This value coincides
with the maximum Jumbo Frames size of 16128.
- Using Jumbo Frames at 10 or 100 Mbps may result in poor performance or
loss of link.
- Some Intel gigabit adapters that support Jumbo Frames have a frame size
limit of 9238 bytes, with a corresponding MTU size limit of 9216 bytes.
The adapters with this limitation are based on the Intel 82571EB and
82572EI controllers, which correspond to these product names:
Intel® PRO/1000 PT Dual Port Server Adapter
Intel® PRO/1000 PF Dual Port Server Adapter
Intel® PRO/1000 PT Server Adapter
Intel® PRO/1000 PT Desktop Adapter
Intel® PRO/1000 PF Server Adapter
The adapters with this limitation are based on the Intel(R) 82571EB,
82572EI, 82573L and 80003ES2LAN controller. These correspond to the
following product names:
Intel(R) PRO/1000 PT Server Adapter
Intel(R) PRO/1000 PT Desktop Adapter
Intel(R) PRO/1000 PT Network Connection
Intel(R) PRO/1000 PT Dual Port Server Adapter
Intel(R) PRO/1000 PT Dual Port Network Connection
Intel(R) PRO/1000 PF Server Adapter
Intel(R) PRO/1000 PF Network Connection
Intel(R) PRO/1000 PF Dual Port Server Adapter
Intel(R) PRO/1000 PB Server Connection
Intel(R) PRO/1000 PL Network Connection
Intel(R) PRO/1000 EB Network Connection with I/O Acceleration
Intel(R) PRO/1000 EB Backplane Connection with I/O Acceleration
Intel(R) PRO/1000 PT Quad Port Server Adapter
- The Intel PRO/1000 PM Network Connection does not support jumbo frames.
- Adapters based on the Intel(R) 82542 and 82573V/E controller do not
support Jumbo Frames. These correspond to the following product names:
Intel(R) PRO/1000 Gigabit Server Adapter
Intel(R) PRO/1000 PM Network Connection
- The following adapters do not support Jumbo Frames:
Intel(R) 82562V 10/100 Network Connection
Intel(R) 82566DM Gigabit Network Connection
Intel(R) 82566DC Gigabit Network Connection
Intel(R) 82566MM Gigabit Network Connection
Intel(R) 82566MC Gigabit Network Connection
Intel(R) 82562GT 10/100 Network Connection
Intel(R) 82562G 10/100 Network Connection
Ethtool
-------
The driver utilizes the ethtool interface for driver configuration and
diagnostics, as well as displaying statistical information. Ethtool
version 1.6 or later is required for this functionality.
@ -423,7 +496,6 @@ Additional Configurations
Enabling Wake on LAN* (WoL)
---------------------------
WoL is configured through the Ethtool* utility. Ethtool is included with
all versions of Red Hat after Red Hat 7.2. For other Linux distributions,
download and install Ethtool from the following website:
@ -436,9 +508,15 @@ Additional Configurations
For this driver version, in order to enable WoL, the e1000 driver must be
loaded when shutting down or rebooting the system.
Wake On LAN is only supported on port A for the following devices:
Intel(R) PRO/1000 PT Dual Port Network Connection
Intel(R) PRO/1000 PT Dual Port Server Connection
Intel(R) PRO/1000 PT Dual Port Server Adapter
Intel(R) PRO/1000 PF Dual Port Server Adapter
Intel(R) PRO/1000 PT Quad Port Server Adapter
NAPI
----
NAPI (Rx polling mode) is supported in the e1000 driver. NAPI is enabled
or disabled based on the configuration of the kernel. To override
the default, use the following compile-time flags.
@ -457,9 +535,15 @@ Additional Configurations
Known Issues
============
Dropped Receive Packets on Half-duplex 10/100 Networks
------------------------------------------------------
If you have an Intel PCI Express adapter running at 10mbps or 100mbps, half-
duplex, you may observe occasional dropped receive packets. There are no
workarounds for this problem in this network configuration. The network must
be updated to operate in full-duplex, and/or 1000mbps only.
Jumbo Frames System Requirement
-------------------------------
Memory allocation failures have been observed on Linux systems with 64 MB
of RAM or less that are running Jumbo Frames. If you are using Jumbo
Frames, your system may require more than the advertised minimum
@ -467,7 +551,6 @@ Known Issues
Performance Degradation with Jumbo Frames
-----------------------------------------
Degradation in throughput performance may be observed in some Jumbo frames
environments. If this is observed, increasing the application's socket
buffer size and/or increasing the /proc/sys/net/ipv4/tcp_*mem entry values
@ -475,15 +558,22 @@ Known Issues
/usr/src/linux*/Documentation/
networking/ip-sysctl.txt for more details.
Jumbo frames on Foundry BigIron 8000 switch
Jumbo Frames on Foundry BigIron 8000 switch
-------------------------------------------
There is a known issue using Jumbo frames when connected to a Foundry
BigIron 8000 switch. This is a 3rd party limitation. If you experience
loss of packets, lower the MTU size.
Allocating Rx Buffers when Using Jumbo Frames
---------------------------------------------
Allocating Rx buffers when using Jumbo Frames on 2.6.x kernels may fail if
the available memory is heavily fragmented. This issue may be seen with PCI-X
adapters or with packet split disabled. This can be reduced or eliminated
by changing the amount of available memory for receive buffer allocation, by
increasing /proc/sys/vm/min_free_kbytes.
Multiple Interfaces on Same Ethernet Broadcast Network
------------------------------------------------------
Due to the default ARP behavior on Linux, it is not possible to have
one system on two IP networks in the same Ethernet broadcast domain
(non-partitioned switch) behave as expected. All Ethernet interfaces
@ -508,7 +598,6 @@ Known Issues
82541/82547 can't link or are slow to link with some link partners
-----------------------------------------------------------------
There is a known compatibility issue with 82541/82547 and some
low-end switches where the link will not be established, or will
be slow to establish. In particular, these switches are known to
@ -521,7 +610,7 @@ Known Issues
of the PHY's master/slave setting. Forcing master or forcing slave
mode will improve time-to-link.
# make EXTRA_CFLAGS=-DE1000_MASTER_SLAVE=<n>
# make CFLAGS_EXTRA=-DE1000_MASTER_SLAVE=<n>
Where <n> is:
@ -532,7 +621,6 @@ Known Issues
Disable rx flow control with ethtool
------------------------------------
In order to disable receive flow control using ethtool, you must turn
off auto-negotiation on the same command line.
@ -540,6 +628,13 @@ Known Issues
ethtool -A eth? autoneg off rx off
Unplugging network cable while ethtool -p is running
----------------------------------------------------
In kernel versions 2.5.50 and later (including 2.6 kernel), unplugging
the network cable while ethtool -p is running will cause the system to
become unresponsive to keyboard commands, except for control-alt-delete.
Restarting the system appears to be the only remedy.
Support
=======
@ -554,18 +649,4 @@ For general information, go to the Intel support website at:
If an issue is identified with the released source code on the supported
kernel with a supported adapter, email the specific information related
to the issue to e1000-devel@lists.sourceforge.net
License
=======
This software program is released under the terms of a license agreement
between you ('Licensee') and Intel. Do not use or load this software or any
associated materials (collectively, the 'Software') until you have carefully
read the full terms and conditions of the file COPYING located in this software
package. By loading or using the Software, you agree to the terms of this
Agreement. If you do not agree with the terms of this Agreement, do not
install or use the Software.
* Other names and brands may be claimed as the property of others.
to the issue to e1000-devel@lists.sf.net