forked from mirrors/linux
ac8fd122e0
request_irq() is preferred over setup_irq(). Invocations of setup_irq() occur after memory allocators are ready. Per tglx[1], setup_irq() existed in olden days when allocators were not ready by the time early interrupts were initialized. Hence replace setup_irq() by request_irq(). remove_irq() has been replaced by free_irq() as well. There were build error's during previous version, couple of which was reported by kbuild test robot <lkp@intel.com> of which one was reported by Thomas Bogendoerfer <tsbogend@alpha.franken.de> as well. There were a few more issues including build errors, those also have been fixed. [1] https://lkml.kernel.org/r/alpine.DEB.2.20.1710191609480.1971@nanos Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
155 lines
4.3 KiB
C
155 lines
4.3 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Copyright (C) 2008-2009 Manuel Lauss <manuel.lauss@gmail.com>
|
|
*
|
|
* Previous incarnations were:
|
|
* Copyright (C) 2001, 2006, 2008 MontaVista Software, <source@mvista.com>
|
|
* Copied and modified Carsten Langgaard's time.c
|
|
*
|
|
* Carsten Langgaard, carstenl@mips.com
|
|
* Copyright (C) 1999,2000 MIPS Technologies, Inc. All rights reserved.
|
|
*
|
|
* ########################################################################
|
|
*
|
|
* ########################################################################
|
|
*
|
|
* Clocksource/event using the 32.768kHz-clocked Counter1 ('RTC' in the
|
|
* databooks). Firmware/Board init code must enable the counters in the
|
|
* counter control register, otherwise the CP0 counter clocksource/event
|
|
* will be installed instead (and use of 'wait' instruction is prohibited).
|
|
*/
|
|
|
|
#include <linux/clockchips.h>
|
|
#include <linux/clocksource.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/spinlock.h>
|
|
|
|
#include <asm/idle.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/time.h>
|
|
#include <asm/mach-au1x00/au1000.h>
|
|
|
|
/* 32kHz clock enabled and detected */
|
|
#define CNTR_OK (SYS_CNTRL_E0 | SYS_CNTRL_32S)
|
|
|
|
static u64 au1x_counter1_read(struct clocksource *cs)
|
|
{
|
|
return alchemy_rdsys(AU1000_SYS_RTCREAD);
|
|
}
|
|
|
|
static struct clocksource au1x_counter1_clocksource = {
|
|
.name = "alchemy-counter1",
|
|
.read = au1x_counter1_read,
|
|
.mask = CLOCKSOURCE_MASK(32),
|
|
.flags = CLOCK_SOURCE_IS_CONTINUOUS,
|
|
.rating = 1500,
|
|
};
|
|
|
|
static int au1x_rtcmatch2_set_next_event(unsigned long delta,
|
|
struct clock_event_device *cd)
|
|
{
|
|
delta += alchemy_rdsys(AU1000_SYS_RTCREAD);
|
|
/* wait for register access */
|
|
while (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_M21)
|
|
;
|
|
alchemy_wrsys(delta, AU1000_SYS_RTCMATCH2);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static irqreturn_t au1x_rtcmatch2_irq(int irq, void *dev_id)
|
|
{
|
|
struct clock_event_device *cd = dev_id;
|
|
cd->event_handler(cd);
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static struct clock_event_device au1x_rtcmatch2_clockdev = {
|
|
.name = "rtcmatch2",
|
|
.features = CLOCK_EVT_FEAT_ONESHOT,
|
|
.rating = 1500,
|
|
.set_next_event = au1x_rtcmatch2_set_next_event,
|
|
.cpumask = cpu_possible_mask,
|
|
};
|
|
|
|
static int __init alchemy_time_init(unsigned int m2int)
|
|
{
|
|
struct clock_event_device *cd = &au1x_rtcmatch2_clockdev;
|
|
unsigned long t;
|
|
|
|
au1x_rtcmatch2_clockdev.irq = m2int;
|
|
|
|
/* Check if firmware (YAMON, ...) has enabled 32kHz and clock
|
|
* has been detected. If so install the rtcmatch2 clocksource,
|
|
* otherwise don't bother. Note that both bits being set is by
|
|
* no means a definite guarantee that the counters actually work
|
|
* (the 32S bit seems to be stuck set to 1 once a single clock-
|
|
* edge is detected, hence the timeouts).
|
|
*/
|
|
if (CNTR_OK != (alchemy_rdsys(AU1000_SYS_CNTRCTRL) & CNTR_OK))
|
|
goto cntr_err;
|
|
|
|
/*
|
|
* setup counter 1 (RTC) to tick at full speed
|
|
*/
|
|
t = 0xffffff;
|
|
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_T1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
|
|
alchemy_wrsys(0, AU1000_SYS_RTCTRIM); /* 32.768 kHz */
|
|
|
|
t = 0xffffff;
|
|
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
alchemy_wrsys(0, AU1000_SYS_RTCWRITE);
|
|
|
|
t = 0xffffff;
|
|
while ((alchemy_rdsys(AU1000_SYS_CNTRCTRL) & SYS_CNTRL_C1S) && --t)
|
|
asm volatile ("nop");
|
|
if (!t)
|
|
goto cntr_err;
|
|
|
|
/* register counter1 clocksource and event device */
|
|
clocksource_register_hz(&au1x_counter1_clocksource, 32768);
|
|
|
|
cd->shift = 32;
|
|
cd->mult = div_sc(32768, NSEC_PER_SEC, cd->shift);
|
|
cd->max_delta_ns = clockevent_delta2ns(0xffffffff, cd);
|
|
cd->max_delta_ticks = 0xffffffff;
|
|
cd->min_delta_ns = clockevent_delta2ns(9, cd);
|
|
cd->min_delta_ticks = 9; /* ~0.28ms */
|
|
clockevents_register_device(cd);
|
|
if (request_irq(m2int, au1x_rtcmatch2_irq, IRQF_TIMER, "timer",
|
|
&au1x_rtcmatch2_clockdev))
|
|
pr_err("Failed to register timer interrupt\n");
|
|
|
|
printk(KERN_INFO "Alchemy clocksource installed\n");
|
|
|
|
return 0;
|
|
|
|
cntr_err:
|
|
return -1;
|
|
}
|
|
|
|
static int alchemy_m2inttab[] __initdata = {
|
|
AU1000_RTC_MATCH2_INT,
|
|
AU1500_RTC_MATCH2_INT,
|
|
AU1100_RTC_MATCH2_INT,
|
|
AU1550_RTC_MATCH2_INT,
|
|
AU1200_RTC_MATCH2_INT,
|
|
AU1300_RTC_MATCH2_INT,
|
|
};
|
|
|
|
void __init plat_time_init(void)
|
|
{
|
|
int t;
|
|
|
|
t = alchemy_get_cputype();
|
|
if (t == ALCHEMY_CPU_UNKNOWN ||
|
|
alchemy_time_init(alchemy_m2inttab[t]))
|
|
cpu_wait = NULL; /* wait doesn't work with r4k timer */
|
|
}
|